Cilindrii compacti seria SDA

Home > AIRTAC > Cilindrii compacti seria SDA

Click pentru a marii

Cod:	SDA
Producator:	AIRTAC

Descriere Imagini aditionale (0) Produse similare (2)

Cilindrii compacti seria SDA

Structura sertizata este preluata pentru a conecta cilindrul de partea din spate, si tija pistonului pentru a il face mai compact si mai sigur.
Diametrul interior al cilindrului este anodizat, formand o rezistenta mare la frecare si durabilitate.
Inchiderea pistonului dispune de o structura de inchidere dubla.Are dimensiune compacta.
Structura compacta poate reduce eficient spatiul de instalare.
Cilindrul dispune de sloturi pt senzori magnetici.

Specificatii

Ø tija mm		12	16	20	25	32	40	50	63	80	100
Tip actiune		Actiune dubla
		Actiune simpla de impingere Actiune simpla de tragere								-
Fluid		Aer( filtrat printr0un filtru de 40µm)
Presiune de lucru	Actiune dubla	0.1~1.0MPa(14~145Psi)
	Actiune simpla	0.2~1.0MPa(28~145Psi)
Presiune maxima		1.5MPa(215Psi)
Temperatura ℃		-20~80
Viteza mm/s		Actiune dubla30~500 Actiune simpla50~500
Toleranta cursa		+1.0 0
Tip de franare		Bumper
Alimentare ①		M5×0.8				1/8"		1/4"		3/8"

① Nota: Filet PT, filet model NPT si model G sunt disponibile.

Cursa

Ø tija mm			Cursa standard mm	Cursa maxima	Cursa disponibila
12 16	Actiune dubla	Cu magnet	5 10 15 20 25 30 35 40 45 50 55	65	70
	Actiune dubla	Fara magnet	5 10 15 20 25 30 35 40 45 50 55 60 65	65	80
	Actiune simpla		5 10 15 20 25 30	30	-
20	Actiune dubla	Cu magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90	100	130
	Actiune dubla	Fara magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100	100	130
	Actiune simpla		5 10 15 20 25 30	30	-
25 32 40 50 63	Actiune dubla	Cu magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120	130	150
	Actiune dubla	Fara magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120 130	130	150
	Actiune simpla		5 10 15 20 25 30	30	-
80 100	Actiune dubla	Cu magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120	130	150
80 100	Actiune dubla	Fara magnet	5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120 130	130	150

Nota: Pt mai multe detalii sau alte tipuri de cilindri va rugam sa ne contactati.

Simbol

Cod comanda

Dimensiuni

Model	Fara magne		Cu magnet		B1	D	E	F	G	K1	L	M	N1		N2
Cota/Ø tija	A	C	A	C	B1	D	E	F	G	K1	L	M	S=5	S>5	S=5	S>5
12	22	17	32	27	5	-	6	4	1	M3×0.5	10.2	3	7.5		5
16	24	18.5	34	28.5	5.5	-	6	4	1.5	M3×0.5	11	3	8		5.5
20	25	19.5	35	29.5	5.5	36	8	4	1.5	M4×0.7	13	3	9		5.5
25	27	21	37	31	6	42	10	4	2	M5×0.8	17	3	9.2		5.5
32	31.5	24.5	41.5	34.5	7	50	12	4	3	M6×1	22	3	9		6.5	9
40	33	26	43	36	7	58.5	12	4	3	M8×1.25	28	3	9.5		7.5
50	37	28	47	38	9	71.5	15	5	4	M10×1.5	38	3	8	10.5	8	10.5
63	41	32	51	42	9	84.5	15	5	4	M10×1.5	40	3	9.5	11.8	9.5	11.8
80	52	41	62	51	11	104	20	6	5	M14×1.5	45	4	11.5	14.5	11.5	14.5
100	63	51	73	61	12	124	20	7	5	M18×1.5	55	4	16	20.5	16	20.5

Cota/Ø tija	O	P1	P3	P4	R	S	T1	T2	V	W	X	Y
12	M5×0.8	2-laturi Ø 6.5 filet :M5×0.8orif.ghidaj Ø 4.2	12	4.5	-	25	16.3	23	6	5	-	-
16	M5×0.8	2-laturi Ø6.5Tfilet M5×0.8Torif.ghidaj Ø4.2	12	4.5	-	29	19.8	28	6	5	-	-
20	M5×0.8	2-laturi Ø6.5filet :M5×0.8orif.ghidaj Ø4.2	14	4.5	2	34	24	-	8	6	11.3	10
25	M5×0.8	2-laturi Ø8.2 filet :M6×1.0orif.ghidaj Ø4.6	15	5.5	2	40	28	-	10	8	12	10
32	1/8"	2-laturi Ø8.2filet :M6×1.0orif.ghidaj Ø4.6	16	5.5	6	44	34	-	12	10	18.3	15
40	1/8"	2-laturi Ø10filet M8×1.25orif.ghidaj Ø6.5	20	7.5	6.5	52	40	-	16	14	21.3	16
50	1/4"	2-laturi Ø11filet :M8×1.25orif.ghidaj Ø6.5	25	8.5	9.5	62	48	-	20	17	30	20
63	1/4"	2-laturi Ø11filet :M8×1.25orif.ghidaj Ø6.5	25	8.5	9.5	75	60	-	20	17	28.7	20
80	3/8"	2-laturi Ø14filet :M12×1.75orif.ghidaj Ø9.2	25	10.5	10	94	74	-	25	22	36	26
100	3/8"	2-laturi Ø17.5filet :M14×2orif.ghidaj Ø11.3	30	13	10	114	90	-	32	27	35	26

SSA

STA

Model	Fara magnet				Cu magnet
Cota/ Ø tija	A		C		A		C
Cursa	≤10	>10	≤10	>10	≤10	>10	≤10	>10
12	32	42	27	37	42	52	37	47
16	34	44	28.5	38.5	44	54	38.5	48.5
20	35	45	29.5	39.5	45	55	39.5	49.5
25	37	47	31	41	47	57	41	51
32	41.5	51.5	34.5	44.5	51.5	61.5	44.5	54.5
40	43	53	36	46	53	63	46	56
50	47	57	38	48	57	67	48	58
63	51	61	42	52	61	71	52	62

Cota/ Ø tija	B1	D	E	F	G	K1	L	M	N1	N2
12	5	-	6	4	1	M3×0.5	10.2	3	7.5	5
16	5.5	-	6	4	1.5	M3×0.5	11	3	8	5.5
20	5.5	36	8	4	1.5	M4×0.7	13	3	9	5.5
25	6	42	10	4	2	M5×0.8	17	3	9.2	5.5
32	7	50	12	4	3	M6×1	22	3	9	9
40	7	58.5	12	4	3	M8×1.25	28	3	9.5	7.5
50	9	71.5	15	5	4	M10×1.5	38	3	10.5	10.5
63	9	84.5	15	5	4	M10×1.5	40	3	12	11

Cota/ Ø tija	O	P1
12	M5×0.8	2-laturi Ø 6.5 filet :M5×0.8 orif.ghidaj Ø 4.2
16	M5×0.8	2-laturi Ø6.5filet M5×0.8 orif.ghidaj Ø4.2
20	M5×0.8	2-laturi Ø6.5filet M5×0.8 orif.ghidaj Ø4.2
25	M5×0.8	2-laturi Ø8.2filet :M6×1.0 orif.ghidaj Ø4.6
32	1/8"	2-laturi Ø8.2filet M6×1.0 orif.ghidaj Ø4.6
40	1/8"	2-laturi Ø10filet M8×1.25 orif.ghidaj Ø6.5
50	1/4"	2-laturi Ø11filet :M8×1.25 orif.ghidaj Ø6.5
63	1/4"	2-laturi Ø11filet :M8×1.25 orif.ghidaj Ø6.5

Cota/ Ø tija	P3	P4	R	S	T1	T2	V	W	X	Y
12	12	4.5	-	25	16.2	23	6	5	-	-
16	12	4.5	-	29	19.8	28	6	5	-	-
20	14	4.5	2	34	24	-	8	6	11.3	10
25	15	5.5	2	40	28	-	10	8	12	10
32	16	5.5	6	44	34	-	12	10	18.3	15
40	20	7.5	6.5	52	40	-	16	14	21.3	16
50	25	8.5	9.5	62	48	-	20	17	30	20
63	25	8.5	9.5	75	60	-	20	17	28.7	20

SDAD

Model	Fara magnet		Cu magnet		E		B1	F	K1	L	N1
Cota/Ø tija	A	C	A	C	S≤10	S>10	B1	F	K1	L	S=5	S>5
12	27	17	37	27	6		5	4	M3×0.5	10.2	5.5	6.3
16	29.5	18.5	39.5	28.5	6		5.5	4	M3×0.5	11	6.5	7.3
20	30.5	19.5	40.5	29.5	8S=5 is 6.5）		5.5	4	M4×0.7	15	7.5
25	33	21	43	31	10S=5 is 7）		6	4	M5×0.8	17	8
32	38.5	24.5	48.5	34.5	8	12	7	4	M6×1	22	8	9
40	40	26	50	36	8	12	7	4	M8×1.25	28	8	10
50	46	28	56	38	8	15	9	5	M10×1.5	38	8	10.5
63	50	32	60	42	10	15	9	5	M10×1.5	40	9.5	11.8
80	63	41	73	51	13	20	11	6	M14×1.5	45	11.5	14.5
100	75	51	85	61	18	20	12	7	M18×1.5	55	16	20.5

Observatie: 1Dimensiunile nespecificate sunt aceleasi cu dimensiunile cilindrilor standard seria SDA.

SDAJ

Model	Fara magnet		Cu magnet		B1	E
Cota/Ø tija	A	C	A	C	B1	S≤10	S>10
12	40	17	50	27	5	6
16	42.5	18.5	52.5	28.5	5.5	6
20	47.5	19.5	57.5	29.5	5.5	8(S=5 is 6.5)
25	55	21	65	31	6	10(S=5 is 7)
32	61.5	24.5	71.5	34.5	7	8	12
40	65	26	75	36	7	8	12
50	73	28	83	38	9	8	15
63	77	32	87	42	9	10	15
80	94	41	104	51	11	13	20
100	105	51	115	61	12	18	20

Cota/Ø tija	Q	K1	L	N1
Cursa	Q	K1	L	S=5	S>5
12	12	M3×0.5	10.2	5.5	6.3
16	12	M3×0.5	11	6.5	7.3
20	15	M4×0.7	15	7.5
25	18	M5×0.8	17	8
32	20	M6×1	22	8	9
40	20	M8×1.25	28	8	10
50	20	M10×1.5	38	8	10.5
63	20	M10×1.5	40	9.5	11.8
80	24	M14×1.5	45	11.5	14.5
100	24	M18×1.5	55	16	20.5

Observatie: 1Dimensiunile nespecificate sunt aceleasi cu dimensiunile cilindrilor standard seria SDA.

SDAT

Model	Fara magnet			Cu magnet			B1	D	E	F	G	K1	L	M	N1		N2		O
Cota/Ø tija	A	C0	C1	A	C0	C1	B1	D	E	F	G	K1	L	M	S=5	S>5	S=5	S>5	O
12	39	34	17	59	54	27	5	-	6	4	1	M3×0.5	10.2	3	7.5		5		M5×0.8
16	42.5	37	18.5	62.5	57	28.5	5.5	-	6	4	1.5	M3×0.5	11	3	8		5.5		M5×0.8
20	44.5	39	19.5	64.5	59	29.5	5.5	36	8	4	1.5	M4×0.7	13	3	9		5.5		M5×0.8
25	48	42	21	68	62	31	6	42	10	4	2	M5×0.8	17	3	9.2		5.5		M5×0.8
32	56	49	24.5	76	69	34.5	7	50	12	4	3	M6×1	22	3	9	6.5	9	6.5	1/8"
40	59	52	26	79	72	36	7	58.5	12	4	3	M8×1.25	28	3	9.5		7.5		1/8"
50	65	56	28	85	76	38	9	71.5	15	5	4	M10×1.5	38	3	8	10.5	8	10.5	1/4"
63	73	64	32	93	84	42	9	84.5	15	5	4	M10×1.5	40	3	9.5	11	9.5	12	1/4"
80	93	82	41	113	102	51	11	104	20	6	5	M14×1.5	45	4	11.5	14.5	11.5	14.5	3/8"
100	114	102	51	134	122	61	12	124	20	7	5	M18×1.5	55	4	16	20.5	16	20.5	3/8"

Cota/Ø tija.	X	Y	W	P1	P2	P3	P4	R	S	T1	T2	V
12			5	2-laturi Ø 6.5 filet :M5×0.8 orif.ghidaj Ø 4.2	-	12	4.5	-	25	16.2	23	6
16	-	-	5	2-laturi Ø 6.5 filet :M5×0.8orif.ghidaj Ø 4.2	-	12	4.5	-	29	19.8	28	6
20	11.3	10	6	2-laturi Ø 6.5 filet M5×0.8orif.ghidaj Ø 4.2	2-laturi Ø 6.5 orif.ghidaj Ø 5.2	14	4.5	2	34	24	-	8
25	12	10	8	2-laturi Ø 8.2 filet M6×1.0 orif.ghidaj Ø 4.6	2-laturi Ø 8.2 orif.ghidaj Ø 6.2	15	5.5	2	40	28	-	10
32	18.3	15	10	2-laturi Ø 8.2 filet M6×1.0 orif.ghidaj Ø 4.6	2-laturi Ø 8.2 orif.ghidaj Ø 6.2	16	5.5	6	44	34	-	12
40	21.8	16	14	2-laturi Ø 10 filet :M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 10 orif.ghidaj Ø 8.2	20	7.5	6.5	52	40	-	16
50	30	20	17	2-laturi Ø 11 filet :M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 11 orif.ghidaj Ø 8.5	25	8.5	9.5	62	48	-	20
63	28.7	20	17	2-laturi Ø 11 filet :M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 11 orif.ghidaj Ø 8.5	25	8.5	9.5	75	60	-	20
80	36	26	22	2-laturi Ø 14 filet :M12×1.75 orif.ghidaj Ø 9.2	2-laturi Ø 14 orif.ghidaj Ø 12.3	25	10.5	10	94	74	-	25
100	35	26	27	2-laturi Ø 17.5 filet :M14×2 orif.ghidaj Ø 11.3	2-laturi Ø 17.5 orif.ghidaj Ø 14.2	30	13	10	114	90	-	32

SDAW

Model	Fara magnet			Cu magnet			B1
Cota/Ø tija	A	CO	C1	A	CO	C1	B1
12	44	34	17	64	54	27	5
16	48	37	18.5	68	57	28.5	5.5
20	50	39	19.5	70	59	29.5	5.5
25	54	42	21	74	62	31	6
32	63	49	24.5	83	69	34.5	7
40	66	52	26	86	72	36	7
50	74	56	28	94	76	38	9
63	82	64	32	102	84	42	9
80	104	82	41	124	102	51	11
100	126	102	51	146	122	61	12

Cota/Ø tija	D	E	F	G	K1	L	M
12	-	6	4	1	M3×0.5	10.2	3
16	-	6	4	1.5	M3×0.5	11	3
20	36	8	4	1.5	M4×0.7	13	3
25	42	10	4	2	M5×0.8	17	3
32	50	12	4	3	M6×1	22	3
40	58.5	12	4	3	M8×1.25	28	3
50	71.5	15	5	4	M10×1.5	38	3
63	84.5	15	5	4	M10×1.5	40	3
80	104	20	6	5	M14×1.5	45	4
100	124	20	7	5	M18×1.5	55	4

Cota/Ø tija	N2			N1			O	X	Y
Cursa	S=5	S>5		S=5		S>5
12	7.5			5			M5×0.8	-	-
16	8			5.5			M5×0.8	-	-
20	9			5.5			M5×0.8	11.3	10
25	9.2			5.5			M5×0.8	12	10
32	9		6.5		9		1/8"	18.3	15
40	9.5			7.5			1/8"	21.3	16
50	8	10.5		8		10.5	1/4"	30	20
63	9.5	11		9.5		12	1/4"	28.7	20
80	11.5	14.5		11.5		14.5	3/8"	36	26
100	16	20.5		16		20.5	3/8"	35	26

Cota/Ø tija	P1	P2
12	2-laturi Ø 6.5 filet: M5×0.8 orif.ghidaj Ø 4.2	-
16	2-laturi Ø 6.5 filet:M5×0.8 orif.ghidaj Ø 4.2	-
20	2-laturi Ø 6.5 filet::M5×0.8 orif.ghidaj Ø 4.2	2-laturi Ø 6.5 orif.ghidaj Ø 5.2
25	2-laturi Ø 8.2 filet:M6×1.0 orif.ghidaj Ø 4.6	2-laturi Ø 8.2 orif.ghidaj Ø 6.2
32	2-laturi Ø 8.2 T filet::M6×1.0 orif.ghidaj Ø 4.6	2-laturi Ø 8.2 orif.ghidaj Ø 6.2
40	2-laturi Ø 10 filet:M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 10 orif.ghidaj Ø 8.2
50	2-laturi Ø 11 filet::M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 11 orif.ghidaj Ø 8.5
63	2-laturi Ø 11 filet:M8×1.25 orif.ghidaj Ø 6.5	2-laturi Ø 11 orif.ghidaj Ø 8.5
80	2-laturi Ø 14 filet::M12×1.75 orif.ghidaj Ø 9.2	2-laturi Ø 14 orif.ghidaj Ø 12.3
100	2-laturi Ø 17.5 filet::M14×2 orif.ghidaj Ø 11.3	2-laturi Ø 17.5 orif.ghidaj Ø 14.2

Cota/Ø tija	W	P3	P4	R	S	T1	T2	V
12	5	12	4.5	-	25	16.2	23	6
16	5	12	4.5	-	29	19.8	28	6
20	6	14	4.5	2	34	24	-	8
25	8	15	5.5	2	40	28	-	10
32	10	16	5.5	6	44	34	-	12
40	14	20	7.5	6.5	52	40	-	16
50	17	25	8.5	9.5	62	48	-	20
63	17	25	8.5	9.5	75	60	-	20
80	22	25	10.5	10	94	74	-	25
100	27	30	13	10	114	90	-	32

Dimensiuni filet exterior.

Cota/Ø tija	B2	E	F	G	H	I	J	K2	L	M	V	W
12	17	16	4	1	10	8	4	M5×0.8	10.2	3	6	5
16	17.5	16	4	1.5	10	8	4	M5×0.8	11	3	6	5
20	20.5	19	4	1.5	13	10	5	M6×1.0	13	3	8	6
25	23	21	4	2	15	12	6	M8×1.25	17	3	10	8
32	25	22	4	3	15	17	6	M10×1.25	22	3	12	10
40	35	32	4	3	25	19	8	M14×1.5	28	3	16	14
50	37	33	5	4	25	27	11	M18×1.5	38	3	20	17
63	37	33	5	4	25	27	11	M18×1.5	40	3	20	17
80	44	39	6	5	30	32	13	M22×1.5	45	4	25	22
100	50	45	7	5	35	36	13	M26×1.5	55	4	32	27